Koraplast SF LQ 60g polyurethane adhesive, contact for rubber, leather, shoes, car tarpaulins, short evaporation time, cold bonding
Product code: 15028342
Leave feedback on the product
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Secure purchase guarantee
Product description
Koraplast SF 60g
Koraplast SF is a contact adhesive based on polyurethane (PUR), containing solvents. It can be used as a single- or two-component cold contact adhesive. This product is ideal for bonding materials exposed to high stress, such as leather, PVC, PUR, rubber and plastics, especially in the automotive industry.
Application
- Bonding materials in the automotive industry: leather, PVC, PUR, rubber, plastics.
- Bonding elements subjected to high mechanical stress.
- Improvement of resistance to heat, moisture, oils, fats and plasticizers by adding a hardener.
Properties
- Base: Polyurethane, containing solvents
- Color: Transparent
- Density: 0.86 g/cm³
- Viscosity: 2700 mPas
- Activation temperature: 40-50 °C
- Hardener: Köracur TR 400, Köracur TR 280
- Mixing ratio: 5-10%
- Pot life: 6-8 hours with Köracur TR 280
- Drying time: 5-20 minutes
Technical parameters
| Parameter | Value |
|---|---|
| Base | Polyurethane, containing solvents |
| Color | Transparent |
| Density | 0.86 g/cm³ |
| Viscosity | 2700 mPas |
| Activation temperature | 40-50 °C |
| Hardener | Köracur TR 400, Köracur TR 280 |
| Ratio mixing | 5-10% |
| Potency | 6-8 hours with Köracur TR 280 |
| Drying time | 5-20 minutes |
Storage and use recommendations
- Store at temperatures above +10°C for a maximum of 12 months.
- The containers must be tightly closed to avoid solvent evaporation.
- Before using the adhesive, it must be stored for at least 3 days at a temperature between +25°C and +35°C if previously stored at lower temperatures. temperatures.
- Leather, rubber and PUR soles should be thoroughly roughened before applying the glue.
- PUR soles should be primed with Kö-PUR.
- PVC should be thoroughly washed and rubber should be halogenated with Halosol S or Halosol 6.
Gluing process
- To improve resistance to heat, moisture, oils, fats and plasticizers, mix 5-10% of Köracur TR 400 or TR 280 hardener with the glue.
- Apply the glue to the surface, taking into account the open times.
- Absorbent materials should be covered twice.
- Wait 5-20 minutes for drying, combine the materials and press.
- If the contact time is exceeded, cold, activate one side at +40°C to +50°C, connect and press.
- The pressing time depends on the hardness of the material and is approximately 8-15 seconds.
Cleaning tools
Use Körasolv CA, Körasolv M, Körasolv PU to clean tools.
Safety
Before use, read the Safety Data Sheet and product labels. Particular attention should be paid to the recommendations regarding hazardous substances. The Safety Data Sheet should be easily accessible, as it contains valuable information on the safe use and disposal of the product and on what to do in the event of an accident involving the product.
Product safety
Manufacturer
HB Fuller Europe GmbH
WERNER-VON-SIEMENS-STR. 2
31515 Wunstorf, Germany
Responsible person in the EU
HB Fuller Europe GmbH
WERNER-VON-SIEMENS-STR. 2
31515 Wunstorf, Germany
Reviews
If you've added a review and it doesn't appear on the list, it may be pending moderation.
Leave feedback on the product
Log in with Google
