MELKIB MB-0247 — Empty 2K Cartridge 400 ml (1:1), Type F Outlet for Static Mixers
Product code: MB-0247
Leave feedback on the product
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Secure purchase guarantee
Product description
What it is and how to use it
MELKIB MB-0247 is an empty, dual-chamber cartridge for two-component materials with a total capacity of 400 ml (2×200 ml) and a fixed 1:1 mix ratio. The Type F outlet is designed for mounting a Type F static mixer, so the components are blended inside the nozzle—no manual mixing required. The cartridge works with standard 2K 1:1 dispensers for the 400 ml format (manual or pneumatic).
Use it wherever repeatability and clean application matter: service, maintenance, assembly, prototyping and small-/medium-batch production. The cartridge is suitable for typical 2K systems (e.g., epoxies, polyurethanes, MMA, MS), while chemical compatibility with the cartridge material and accessories should be confirmed by a quick test on your target substrate.
Why it’s a good choice
• Fixed 1:1 ratio — two equal chambers support correct dosing of both components
• Type F outlet — quick installation of Type F static mixers and consistent in-nozzle mixing
• Compact 400 ml format — handy for mobile work and shorter bead runs; reduces leftovers per cycle
• Versatile use — epoxies, PU, MMA, MS (user to verify chemical compatibility)
Best-fit applications
Service and assembly work, structural bonding, composite repairs, potting/laminating of parts, prototyping and shorter production runs with two-component materials.
Technical parameters
| Parameter | Value |
|---|---|
| Product code | MB-0247 |
| Brand | MELKIB |
| Cartridge type | Dual (2K), 1:1 configuration |
| Mix ratio | 1:1 (two equal chambers) |
| Total capacity | 400 ml (2 × 200 ml) |
| Outlet type | Type F (for Type F static mixers) |
| Mixer compatibility | Type F static mixers — choose length/diameter to suit viscosity and pot life |
| Dispensing tools | Manual or pneumatic dispensers for 2K 400 ml (1:1) cartridges |
| Intended use | Most 2K adhesives/resins (epoxies, PU, MMA, MS); chemical compatibility must be verified |
How to use
1) Fill both chambers with components A and B (1:1). 2) Close the cartridge per your procedure (plungers/end caps). 3) Place the cartridge in a 2K (1:1) dispenser. 4) Fit a Type F mixer and purge with a short extrude to waste. 5) Dispense directly onto the parts to be bonded or into the mold.
Storage
Store the empty cartridge in a dry, clean place, away from heat sources and UV radiation. Prevent contamination inside the chambers. Room-temperature storage is recommended.
FAQ – most common questions
2K 400 ml 1:1 Type F cartridge — which dispensers does it fit?
Dual-cartridge 2K dispensers in the 400 ml standard and 1:1 ratio. Before purchase, check that your applicator supports 2×200 ml.
Which mixer for a 1:1 Type F 400 ml cartridge?
Type F static mixers. Select length and diameter to match material viscosity and pot life (thicker material → longer/wider mixer).
Is Type F the same as Type C?
No. They are different nozzle-mount standards. MB-0247 works with Type F mixers and accessories.
Is the 400 ml 1:1 cartridge suitable for epoxies and polyurethanes?
Yes, for typical 2K systems (epoxy, PU, MMA, MS). Confirm chemical compatibility with the cartridge material by a quick test on the target substrate.
How to reduce air bubbles when filling?
Fill slowly and vertically; after installing the mixer, make a short purge to waste until a uniform mix flows out.
Is a 2K 1:1 400 ml cartridge reusable?
The cartridge is intended to be consumed with the material. After work you replace the nozzle; once fully emptied, dispose of it in line with regulations.
Which accessories are needed to start?
A 2K 400 ml (1:1) dispenser, a suitable Type F mixer, plungers/end caps. See also Type F static mixers.
Product safety
Manufacturer
Melkib Klus Raczek Spółka Komandytowa
ul. Stawowa 91
43-400 Cieszyn, Poland
Responsible person in the EU
Melkib Klus Raczek Spółka Komandytowa
ul. Stawowa 91
43-400 Cieszyn, Poland
Reviews
If you've added a review and it doesn't appear on the list, it may be pending moderation.
Leave feedback on the product
Log in with Google
