WEICON Easy-Mix Metal 50 ml 2K epoxy adhesive for metal heat-resistant up to 180°C
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Secure purchase guarantee
Opis produktu
WEICON Easy-Mix Metal 50 ml – two-component epoxy adhesive for metal with temperature resistance up to +180°C
WEICON Easy-Mix Metal 50 ml is a fast-curing two-component epoxy adhesive developed specifically for bonding metal parts. Its highly filled, pasty formulation combines high mechanical strength, impact resistance and temperature resistance from -50°C to +180°C.
The adhesive is particularly suitable for applications where bonding surfaces are not perfectly matched and gaps need to be bridged. It can fill gaps up to 4 mm and forms a strong, impact-resistant bond after curing.
The 50 ml dual cartridge provides a controlled 1:1 mixing ratio when used with a compatible static mixing nozzle and dispensing device.
Applications of WEICON Easy-Mix Metal
Easy-Mix Metal is primarily intended for bonding metal parts. It can also be used with other suitable materials, including selected plastics and fibre composites, in accordance with the manufacturer's technical documentation.
Typical industrial applications
- Bonding steel and aluminium components in metal structures.
- Joining metal parts during machinery and equipment assembly.
- Industrial maintenance and repair work.
- Bonding metal to suitable plastics or composite materials.
- Filling gaps and irregularities between mating surfaces.
- Assembly operations requiring impact resistance and relatively fast strength development.
Key benefits of WEICON Easy-Mix Metal
Temperature resistance up to +180°C
According to the current manufacturer's technical data, the cured adhesive provides temperature resistance from -50°C to +180°C. The suitability of the bond under actual operating conditions must be assessed with regard to mechanical loads, temperature exposure and the materials being joined.
Fast curing
The working time is approximately 4–5 minutes at +20°C. Handling strength corresponding to 35% of final strength is reached after approximately 20 minutes. Mechanical strength corresponding to 80% is reached after approximately 40 minutes. Final strength is achieved after 24 hours under the specified conditions.
Gap-filling capability up to 4 mm
The pasty, highly filled formulation allows the adhesive to bridge gaps and compensate for irregularities between bonded components. This makes it particularly useful where a perfectly close-fitting joint cannot be achieved.
High mechanical strength
WEICON specifies a lap shear strength of 20 N/mm² on sandblasted steel and 10 N/mm² on sandblasted aluminium. These values are based on defined laboratory testing conditions and surface preparation procedures.
When should you choose WEICON Easy-Mix Metal?
This epoxy adhesive is suitable for applications where metal components must be joined with a combination of rapid strength development, impact resistance, gap-filling capability and elevated temperature resistance.
It is a practical option for industrial assembly and repair processes, provided the bonded joint is properly designed and validated for the intended loads and operating conditions.
How to use WEICON Easy-Mix Metal 50 ml
Surface preparation
Bonding surfaces must be clean, dry and free from grease and loose contamination. WEICON recommends cleaning and degreasing with WEICON Surface Cleaner. Suitable mechanical surface preparation may also be used depending on the substrate.
Mixing and application
- Prepare the 50 ml dual cartridge and a compatible WEICON Easy-Mix D 50 dispenser or manual dispensing device.
- Attach the appropriate WEICON Helix Mixing Nozzle A.
- Begin dispensing and discard the first 5 cm of the mixed adhesive bead as instructed by the manufacturer.
- Apply adhesive to one of the prepared bonding surfaces.
- Join the components and keep them properly positioned during curing.
- Allow the joint to develop sufficient strength before handling or mechanical loading.
Important: higher temperatures shorten both working time and curing time. Lower temperatures extend these times. The specified working time refers to a defined material quantity under laboratory conditions.
Important considerations before use
- Recommended processing temperature: +15°C to +40°C.
- Component temperature should be more than 3°C above the dew point.
- Relative humidity during application should not exceed 85%.
- Maximum specified gap-filling capability: 4 mm.
- Use only a compatible mixing nozzle and dispensing system.
- For safety-critical or load-bearing applications, carry out appropriate tests on the actual substrates and joint design.
Technical specifications – WEICON Easy-Mix Metal 50 ml
| Parameter | Value |
|---|---|
| Manufacturer | WEICON |
| Manufacturer part number | 10018047 |
| Product type | Two-component epoxy adhesive |
| Volume | 50 ml |
| Packaging | Dual cartridge |
| Chemical base | Epoxy resin |
| Colour of mixture | Grey |
| Consistency | Pasty, gap-filling |
| Mixing ratio by volume | 1:1 |
| Viscosity at +20°C | 55,000 mPa·s |
| Density of mixture | 1.8 g/cm³ |
| Maximum gap filling | 4 mm |
| Processing temperature | +15°C to +40°C |
| Curing temperature | +6°C to +40°C |
| Working time at +20°C | 4–5 minutes (10 g batch) |
| Handling strength | 20 minutes (35% of final strength) |
| Mechanical load-bearing strength | 40 minutes (80% of final strength) |
| Final curing time | 24 hours |
| Temperature resistance | -50°C to +180°C |
| Tensile strength | 28 N/mm² |
| Lap shear strength – sandblasted steel | 20 N/mm² |
| Lap shear strength – sandblasted aluminium | 10 N/mm² |
| Shore D hardness | 83 ±3 |
| Minimum shelf life | 18 months under recommended storage conditions |
Storage
Store unopened cartridges in a dry location at temperatures between +18°C and +25°C. Protect from direct sunlight, freezing conditions and significant temperature fluctuations. The manufacturer specifies a minimum shelf life of 18 months when the recommended storage conditions are maintained.
FAQ – frequently asked questions
Is WEICON Easy-Mix Metal suitable for aluminium?
Yes. WEICON confirms suitability for aluminium bonding. A lap shear strength of 10 N/mm² is specified for sandblasted aluminium under defined test conditions.
Can it be used on stainless steel?
Yes. The current technical data includes test results for sandblasted V2A stainless steel. Proper surface preparation is essential.
What is the maximum gap that the adhesive can fill?
The specified maximum gap-filling capability is 4 mm.
How long does WEICON Easy-Mix Metal take to cure?
The working time is approximately 4–5 minutes at +20°C. Handling strength is reached after approximately 20 minutes, while full curing takes 24 hours under the manufacturer's specified conditions.
Which mixing nozzle is compatible with Easy-Mix Metal?
The manufacturer specifies the WEICON Helix Mixing Nozzle A. Quadro A should not be substituted without verified compatibility.
Is a mixing nozzle included in the package?
According to the current technical data, the scope of delivery includes the adhesive and a Helix A mixing nozzle. A dispensing device is a separate accessory.
Can the adhesive withstand +180°C?
WEICON specifies temperature resistance up to +180°C. Suitability for a particular joint depends on mechanical loading, duration of temperature exposure and the overall application conditions.
Reviews
If you've added a review and it doesn't appear on the list, it may be pending moderation.

