Tensorgrip L17 contact adhesive with high thermal resistance 500ml
Product code: L17 500ml
Leave feedback on the product
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Secure purchase guarantee
Product description
Tensorgrip L17 is a unique, high-performance contact adhesive that creates durable bonds between surface-treated materials and conventional wood-based materials. It is suitable for bonding HPL, GRP, aluminium, MDF, chipboard, plywood and many other materials. It is designed for applications requiring a strong adhesive with immediate grab and high temperature resistance.
Advantages
- Class 1 fire rating.
- Bond strength meets the requirements of BS 6222.
- High temperature resistance up to 120°C.
- IMO certified.
Applications
- Aluminium
- Standard laminates
- Fibre-reinforced laminates
- Carbon fibre
- Plasterboards
Technical data
Chemical technical data
| Chemical technical data | |
|---|---|
| Colour | Transparent or green |
| Viscosity | 300 cps 25°C sp#2, 30 r.p.m. |
| Total solids content | 28–30% |
| System flammability | Flammable adhesive solution in a flammable propellant |
| Shear strength | > 250 p.s.i. |
| Tensile strength – 180° peel test | > 25 psi, 90° peel test (6.25 cm²) > 25 psi |
| Delamination temperature (SAFT), 100 grams | > 120°C |
| Drying time | 2–3 minutes |
| Open time | 40 minutes |
| Shelf life | 18 months from the date of manufacture |
| Packaging | 500 ml / 22 l |
Application
Handling and storage
- Read the safety data sheet before use.
- Do not store at temperatures above 50°C.
- Avoid exposure to direct sunlight.
- For maximum performance, use the adhesive at a temperature of 18°C, but always above 10°C.
- Do not store directly on a concrete floor.
- Condition the substrates at a normal room temperature of 18°C for 48 hours before bonding.
- Do not exceed the adhesive open time.
- It is recommended to test the product to determine its suitability for the intended application before using it in production.
Instructions for use
- The product has been designed to be sprayed onto two surfaces to bond them together. For the best results, the temperature of the adhesive and the bonded materials should be between 16°C and 27°C.
- Use in adequately ventilated areas. Shake the container thoroughly before use.
- Before use, check compatibility by spraying a small test amount of adhesive onto the surface. This product may degrade some substrates.
- Ensure that the surfaces to be bonded are dry, clean and free from dust, grease, wax, paint residues, lubricant and other contaminants.
- Spray from a distance of 10–20 cm at a 90° angle to the substrate until a uniform and even adhesive layer covering 80 to 100% of the bonded surfaces is obtained. If necessary, apply another layer of adhesive to areas where coverage is insufficient.
- Apply the adhesive to both surfaces being bonded. Spray one surface vertically and the other horizontally.
- Wait 1–3 minutes for the solvent to evaporate. The time may vary depending on the thickness of the adhesive coating and external conditions such as temperature and humidity.
- Join the components and press them together. The greater the pressure applied, the higher the bond strength. We recommend using a roller to obtain even and firm pressure. The bond reaches its final strength after 24 hours.
Container replacement and storage
Set the container valve to the off position, spray out the adhesive remaining in the hose and disconnect the spray hose and gun from the container. Connect the spray hose to a container of clean solvent, sold separately, and spray until the liquid runs clear. This indicates that the hose and gun have been cleaned. If the hose and spray gun remain connected to the container, open the container valve. Do not disconnect the hose or gun from the container. Close and lock the spray gun.
Product safety
Manufacturer
Quin Global
Unit 1, Ruthvenfield Avenue
PH1 3WB Perth, United Kingdom
Responsible person in the EU
Melkib Klus Raczek Spółka Komandytowa
ul. Stawowa 91
43-400 Cieszyn, Poland
Reviews
If you've added a review and it doesn't appear on the list, it may be pending moderation.
Leave feedback on the product
Log in with Google
